2025 HAYBUSTER H1130 For Sale in (2025)

Description

HAYBUSTER H-1130 BIG BITE—TUB GRINDERSThe H-1130 Big Bite tub grinder is Haybuster’s heavy-duty PTO grinder. It is designed with the features and the durability you need in a 11’ tub grinder. Some of these features include tub tilt, heavy hammermill with ½” plates and ½” hammers along with 1 ¼” rods, dual augers and a 26’ long stacking conveyor. The 315 hp drive system consists of an 8-groove belt/pulley system powered through a 77 series PTO driveline. The belt system tension is set at the factory and is designed to maintain its desired tension when stretching.FEATURES• The dual 12” belly augers are suspended by two heavy-duty bearings and are located at the base of the newly-designed screen area. The auger system allows for a sealed under-screen discharge area. The larger discharge area also provides for higher capacities and reduces the potential for plugging.• The Big Bite 50” heavy-duty hammermill is now standard equipment and is located at the rear of the tub to reduce the length of the discharge. This, along with the increased area around and under the screens accelerates product discharge and reduces the potential of plugging. The heavy-duty hammermill operates at 2140 rpm and is constructed with 88 ½” swinging hammers. The hammers are hardened and are held in place with 1 ¼” case-hardened hammer rods. The hammermill is mounted on a 3 ½” stress-proof shaft supported by 3 ¼” bearings.• The DuraTech electronic governor slows protection for the tractor and the machine. This governor maintains a constant load on the tractor and driveline by adjusting the tubs rpm which controls the feed rate of the material to the hammermill.• The belt drive system for the hammermill has 8-5 VP belts to handle the increased rotor speed and increased horsepower capacity. The spring tension belt drive automatically adjusts belt tension as the belts stretch.• The tub drive has continuous teeth around the tub and dual spring tensioners. Power is provided by a single hydraulic motor controlled by the electronic governor.• The new heavy-duty bolt-in mill grate/9 bar mill grate combination is designed to allow the operator the ability to change the number of mill grate bars and slug bars as grinding conditions change• The large H-1130 Big Bite Tub is constructed of a 10-gauge steel floor and a 12-gauge steel side wall. The width of the tub is 11’ 3”, is 50” deep and can handle the largest round and square bales.• The H-1130’s tub opens a full 90 degrees for easy access to the hammermill and drive train for service and maintenance.• The hydraulic folding 24” wide by 26’ long high-capacity stacking conveyor is designed for the increased capacity of the H-1130 it can stack material 18’6” high.• Large 16.5 x 16.1, 14-ply flotation implement tires provide for easy transportation and a solid base for the H-1130.• High-capacity grain grinding can also be done with the H-1130 tub grinder. Just add in the grain hopper and changes the screens and you have a high capacity grain grinder for grinding and/or cracking feed grains.OPTIONAL FEATURES• PTO Shaft -1000 RPM: Tractor Half, 1-3/4 in, 20 Spline Shaft• PTO Shaft -1000 RPM: Tractor Half, 1-3/8 in, 21 Spline Shaft• Hammermill Feeding Slug Buster, 5 tooth screen hold down• Hammermill Feeding Mill Grate, for grinding tough hay or crop residues• Geyser Plate Kit, use with the Slug Buster• Geyser Plate Kit, slotted, use with the Mill Grate• Hopper for Grain Grinding• Ear Corn Kit• Closed Center Conversion Kit is required to operate the conveyor lift valve properly, with John Deere 60 and older series tractors.GRINDING SCREENS OPTIONS• 1/8 in. (3.18 mm) Round Hole Screen Half*• 3/16 in. (4.76 mm) Round Hole Screen Half**• 1/4 in. (6.35 mm) Round Hole Screen Half• 3/8 in. (9.52 mm) Round Hole Screen Half• 1/2 in. (12.7 mm) Round Hole Screen Half• 5/8 in. (15.88 mm) Round Hole Screen Half• 3/4 in. (19.05 mm) Round Hole Screen Half• 1 in. (25.4 mm) Round Hole Screen Half• 1-1/2 in. (38.1 mm) Round Hole Screen Half• 2 in. (50.8 mm) Round Hole Screen Half• 3 in. (7.62 cm) Round Hole, Screen Half (standard)• 4 in. (10.16 cm) Round Hole, Screen Half (standard)• 5 in. (12.70 cm) Round Hole, Screen Half (standard)• 6 in. (15.24 cm) Round Hole, Screen Half (standard)• 7 in. (17.78 cm) Round Hole, Screen Half (standard)• 8 in. (20.32 cm) Round Hole, Screen Half (standard)• Dummy (Open) Screen Half*1/8 in. (3.18 mm) thick,**3/16 in. (4.76 mm) thick, all other screens are 1/4 in. (6.35 mm) thickHAYBUSTER'S BIG BITE LINE OF TUB GRINDERS PROVIDE SOLUTIONS FOR:• Grinding Hay - big round & square bales, loose hay• Grinding Crop Residues - straw, stover and other types• Grinding Grain - corn, sorghum, and all cereal grains• Commercial grinding applicationsSimilar models may be shown in addition to the featured model. Equipment may be shown with options. Specifications are subject to change without prior notice.